Cooper-instruments-systems LTL 730 Wireless Tension Link Load Cell User Manual download pdf

LTL Quick User Guide January 3, 2008 LTL_QUG_en_500201.fm AWT35-500201 Issue AA

LTL Quick User Guide

Introduction

The LTL electronic dynamometer is a force measurement load sensor and digital readout in one instrument. The LTL can be

used to measure tension or weight. A Communicator can remotely view the display and control the instrument. Check your

user manual CD for complete setup and operating instructions.

Installing Batteries

Unscrew and remove the battery compartment cover. Place two ‘C’ size batteries into the battery compartment as shown

below and screw the cover back on tightly.

Communicator

The Communicator has 4 AA batteries. To replace, remove rear battery cover and replace with fresh batteries in the proper

arrangement.

Battery LIfe

The time required between battery changes can vary with usage, functions enabled, temperature, duration of use and

recovery time, display update rate, battery grade and more.

To maximize battery life:

• Disable radio if not being used. Even if an optional radio board is not installed, the software will run, if

enabled.

• Disable other functions such as RS-232 and backlight.

• Warm environments result in longer battery life over cool environments.

• Use high quality alkaline batteries.

• Turn off instrument when not in use. Alkaline batteries partially recover when the instrument is off.

Î Please note... Remove batteries from the instrument when using the external AC power supply

Care

The LTL is built to be rugged and endure typical industrial and commercial use. It is still, however, a precision instrument that

should be treated with care. Store the instrument in its carry case with power off. Remove batteries if not being used.

Accuracy

Cooper -supplied shackle pins and centering spacers provided by are required to achieve highest accuracy. The force being

measured must be in line with the unit. Apply load in the center of the shackle bows & insure the instrument is centered on

the shackle pin. Torque and bending loads should be relieved.

1 2 3 4

Summary of Contents

Page 1 - LTL Quick User Guide

LTL Quick User Guide January 3, 2008 LTL_QUG_en_500201.fm AWT35-500201 Issue AA LTL Quick User Guide Introduction The LTL electronic dynamometer

Page 2

LTL Quick User Guide January 3, 2008 LTL_QUG_en_500201.fm AWT35-500201 Issue AA Check your user manual on the CD for further detail on obtaining be

Page 3 - Configuration Menu

LTL Quick User Guide January 3, 2008 LTL_QUG_en_500201.fm AWT35-500201 Issue AA Capture of a new peak value. This annunciator will remain lit for

Page 4 - Common Configurations

LTL Quick User Guide January 3, 2008 LTL_QUG_en_500201.fm AWT35-500201 Issue AA Common Configurations LTL being used stand-alone (no RS-232 or Co

Cooper-instruments-systems LTL 730 Wireless Tension Link Load Cell User Manual

Browse online or download User Manual for Measuring instruments Cooper-instruments-systems LTL 730 Wireless Tension Link Load Cell. Cooper Instruments & Systems LTL 730 Wireless Tension Link Load Cell User Manual

Summary of Contents

More documents for Measuring instruments Cooper-instruments-systems LTL 730 Wireless Tension Link Load Cell

Comments to this Manuals

Cooper-instruments-systems LTL 730 Wireless Tension Link Load Cell User Manual

Browse online or download User Manual for Measuring instruments Cooper-instruments-systems LTL 730 Wireless Tension Link Load Cell. Cooper Instruments & Systems LTL 730 Wireless Tension Link Load Cell User Manual

Summary of Contents

More documents for Measuring instruments Cooper-instruments-systems LTL 730 Wireless Tension Link Load Cell

Comments to this Manuals

Related products and manuals for Measuring instruments Cooper-instruments-systems LTL 730 Wireless Tension Link Load Cell